COCKPIT 1U
Compact, performance oriented 4 channel stereo mixer with sidechain ducking
4 channel stereo performance mixer
Daltonic friendly - the LEDs are blue/red instead of red/green
Channel 1 features a stereo input jack, Channels 2/3/4 are dual mono
On-board compressor with external sidechain control voltage option (3 modes) to add dynamics to your mix.
Stereo output for speakers or headphones with enough current to drive a wide range of headphones
extra aux, stereo out, balanced output pins, compatible with Intellijel Audio Jacks V2 Boards / cases
available in 3U / 6HP version
POWER CONSUMPTION:
40 mA +12V
25 mA -12V
0 mA 5V
DIMENSIONS:
24 HP (1U)
42 mm deep (fits all Intellijel Palette cases etc).
Modulargrid: BLACK / SILVER
Manual: COCKPIT 2 / 1U NEW MANUAL / OLD MANUAL
DEFINITIVE UPDATE: COCKPIT 3U / 1U 12-NOV-23
Want to pimp up your module’s look? Check its faceplate replacement & knobs
FAQ:
I cannot switch the algorithm of the Sidechain Compressor. Make sure the encoder buttons work properly i.e they mute/unmute each channel. Also make sure you press all 4 encoders at once. Holding for 1 second while they being pressed will switch the mode in which the Cockpit is indicated by blinking of the blue LED. The mode is stored in a few seconds and will load on the next module's power up.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
What cables are supplied with Cockpit 1U module. 10-10 ribbon power cable, 6-6 ribbon cable for balanced output into Intellijel Audio Jacks V2 board. Note: you have to get dupont daily chain (a.k.a. mixup) wires on your own.
Compact, performance oriented 4 channel stereo mixer with sidechain ducking
4 channel stereo performance mixer
Daltonic friendly - the LEDs are blue/red instead of red/green
Channel 1 features a stereo input jack, Channels 2/3/4 are dual mono
On-board compressor with external sidechain control voltage option (3 modes) to add dynamics to your mix.
Stereo output for speakers or headphones with enough current to drive a wide range of headphones
extra aux, stereo out, balanced output pins, compatible with Intellijel Audio Jacks V2 Boards / cases
available in 3U / 6HP version
POWER CONSUMPTION:
40 mA +12V
25 mA -12V
0 mA 5V
DIMENSIONS:
24 HP (1U)
42 mm deep (fits all Intellijel Palette cases etc).
Modulargrid: BLACK / SILVER
Manual: COCKPIT 2 / 1U NEW MANUAL / OLD MANUAL
DEFINITIVE UPDATE: COCKPIT 3U / 1U 12-NOV-23
Want to pimp up your module’s look? Check its faceplate replacement & knobs
FAQ:
I cannot switch the algorithm of the Sidechain Compressor. Make sure the encoder buttons work properly i.e they mute/unmute each channel. Also make sure you press all 4 encoders at once. Holding for 1 second while they being pressed will switch the mode in which the Cockpit is indicated by blinking of the blue LED. The mode is stored in a few seconds and will load on the next module's power up.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
What cables are supplied with Cockpit 1U module. 10-10 ribbon power cable, 6-6 ribbon cable for balanced output into Intellijel Audio Jacks V2 board. Note: you have to get dupont daily chain (a.k.a. mixup) wires on your own.
Compact, performance oriented 4 channel stereo mixer with sidechain ducking
4 channel stereo performance mixer
Daltonic friendly - the LEDs are blue/red instead of red/green
Channel 1 features a stereo input jack, Channels 2/3/4 are dual mono
On-board compressor with external sidechain control voltage option (3 modes) to add dynamics to your mix.
Stereo output for speakers or headphones with enough current to drive a wide range of headphones
extra aux, stereo out, balanced output pins, compatible with Intellijel Audio Jacks V2 Boards / cases
available in 3U / 6HP version
POWER CONSUMPTION:
40 mA +12V
25 mA -12V
0 mA 5V
DIMENSIONS:
24 HP (1U)
42 mm deep (fits all Intellijel Palette cases etc).
Modulargrid: BLACK / SILVER
Manual: COCKPIT 2 / 1U NEW MANUAL / OLD MANUAL
DEFINITIVE UPDATE: COCKPIT 3U / 1U 12-NOV-23
Want to pimp up your module’s look? Check its faceplate replacement & knobs
FAQ:
I cannot switch the algorithm of the Sidechain Compressor. Make sure the encoder buttons work properly i.e they mute/unmute each channel. Also make sure you press all 4 encoders at once. Holding for 1 second while they being pressed will switch the mode in which the Cockpit is indicated by blinking of the blue LED. The mode is stored in a few seconds and will load on the next module's power up.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
What cables are supplied with Cockpit 1U module. 10-10 ribbon power cable, 6-6 ribbon cable for balanced output into Intellijel Audio Jacks V2 board. Note: you have to get dupont daily chain (a.k.a. mixup) wires on your own.
