COCKPIT MK1
4 Stereo Channel Performance Mixer with Sidechain Ducking
DISCONTINUED
4 stereo channels performance mixer
On-board compressor with external sidechain control voltage option to add proper dynamics to your mix
Stereo output for speakerphones or headphones with enough current to drive a wide range of headphones
new versions available: Cockpit 2 and Cockpit 1U
Power consumption:
75 mA +12V
4 mA -12V
0 mA 5V
Dimensions:
6 HP
38 mm deep
Modulargrid: BLACK / GOLDEN
Manual: HERE
FAQ:
I cannot switch the algorithm of the Sidechain Compressor. Make sure the encoder buttons work properly i.e. they mute/unmute each channel. Also make sure you press all 4 encoders at once. Holding for 1 second while they being pressed will switch the mode in which the Cockpit is indicated by blinking of the blue LED. The mode is stored after a few seconds and will load on the next power up.
Can I utilize other gear than iOS devices to use the send/return jacks of the Cockpit, such as guitar pedals etc.? Cockpit is designed to be used with iOS device’s external input using the TRRS cable (delivered with the Cockpit). The signal routed to the external microphone input of an iOS device via 3.5mm jack is very low, around < 40 mV (peak to peak) and therefore it is attenuated inside the Cockpit module. Therefore it is unusable with normal effect processors.
How can I replace the panel with other color? Check the merch store and panels replacement guide. Also don’t forget the knobs and buttons.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
4 Stereo Channel Performance Mixer with Sidechain Ducking
DISCONTINUED
4 stereo channels performance mixer
On-board compressor with external sidechain control voltage option to add proper dynamics to your mix
Stereo output for speakerphones or headphones with enough current to drive a wide range of headphones
new versions available: Cockpit 2 and Cockpit 1U
Power consumption:
75 mA +12V
4 mA -12V
0 mA 5V
Dimensions:
6 HP
38 mm deep
Modulargrid: BLACK / GOLDEN
Manual: HERE
FAQ:
I cannot switch the algorithm of the Sidechain Compressor. Make sure the encoder buttons work properly i.e. they mute/unmute each channel. Also make sure you press all 4 encoders at once. Holding for 1 second while they being pressed will switch the mode in which the Cockpit is indicated by blinking of the blue LED. The mode is stored after a few seconds and will load on the next power up.
Can I utilize other gear than iOS devices to use the send/return jacks of the Cockpit, such as guitar pedals etc.? Cockpit is designed to be used with iOS device’s external input using the TRRS cable (delivered with the Cockpit). The signal routed to the external microphone input of an iOS device via 3.5mm jack is very low, around < 40 mV (peak to peak) and therefore it is attenuated inside the Cockpit module. Therefore it is unusable with normal effect processors.
How can I replace the panel with other color? Check the merch store and panels replacement guide. Also don’t forget the knobs and buttons.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
4 Stereo Channel Performance Mixer with Sidechain Ducking
DISCONTINUED
4 stereo channels performance mixer
On-board compressor with external sidechain control voltage option to add proper dynamics to your mix
Stereo output for speakerphones or headphones with enough current to drive a wide range of headphones
new versions available: Cockpit 2 and Cockpit 1U
Power consumption:
75 mA +12V
4 mA -12V
0 mA 5V
Dimensions:
6 HP
38 mm deep
Modulargrid: BLACK / GOLDEN
Manual: HERE
FAQ:
I cannot switch the algorithm of the Sidechain Compressor. Make sure the encoder buttons work properly i.e. they mute/unmute each channel. Also make sure you press all 4 encoders at once. Holding for 1 second while they being pressed will switch the mode in which the Cockpit is indicated by blinking of the blue LED. The mode is stored after a few seconds and will load on the next power up.
Can I utilize other gear than iOS devices to use the send/return jacks of the Cockpit, such as guitar pedals etc.? Cockpit is designed to be used with iOS device’s external input using the TRRS cable (delivered with the Cockpit). The signal routed to the external microphone input of an iOS device via 3.5mm jack is very low, around < 40 mV (peak to peak) and therefore it is attenuated inside the Cockpit module. Therefore it is unusable with normal effect processors.
How can I replace the panel with other color? Check the merch store and panels replacement guide. Also don’t forget the knobs and buttons.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
